Wheelock TPI-100 Manual de Instruções descarregar pdf

P82030 K

Sheet 1 of 17

273 Branchport Avenue

Long Branch, NJ 07740 Thank you for using our products.

(800) 631-2148

www.wheelockinc.com

INSTALLATION INSTRUCTIONS

MODEL TPI-100

TELEPHONE PAGING RING START INTERFACE

Use this product according to this instruction manual. Please keep this instruction manual for future reference.

APPLICATION INFORMATION:

Wheelock Inc. manufactures high quality telephone products. The installation of this product must conform to the following

instructions.

IF ANY WORDS OR LETTERS APPEAR ON THE PRODUCT INDICATING A PARTICULAR USE, THE PRODUCT

MUST BE USED ONLY IN THE MANNER SO INDICATED. THE INSTALLATION OF THIS EQUIPMENT SHOULD ONLY BE

UNDERTAKEN BY QUALIFIED PERSONNEL. FIELD ADJUSTMENT, REPAIR OR MODIFICATION OF THESE SIGNALS SHOULD

NOT BE ATTEMPTED. Malfunctioning units should be returned for factory repair or replacement in accordance with Wheelock

Inc.'s published terms and conditions. Contact Wheelock Inc., 273 Branchport Ave., Long Branch, NJ, 07740.

NOTE

: All

CAUTIONS

and

WARNINGS

are identified by the symbol . All warnings are printed in bold capital letters.

FCC REGULATIONS

- This equipment complies with Part 68 of the FCC Rules. The label affixed to this product contains, among other

information, the FCC Registration Number and the Ringer Equivalence Number (REN) for this product. This information

must be provided to the telephone company if requested.

- The REN is used to determine the quantity of devices which you may connect to your telephone line and still have all of

those devices ring when your telephone number is called. In most, but not all areas, the sum of the REN's of all devices

connected to one line should not exceed five (5.0). To be certain of the number of devices that you may connect to your

line, contact your local telephone company.

- This equipment should not be used on coin telephone lines. Connection to party line service is subject to state tariffs.

- If trouble is experienced, disconnect this equipment from the telephone line to determine if it is causing the malfunction. If

the equipment is determined to be malfunctioning, its use shall be discontinued until the problem has been corrected.

- Should the equipment cause harm to the telephone network, the telephone company shall, if possible, notify the customer

that temporary discontinuance of service may be required; however, where prior written notice is not possible, the

telephone company may temporarily discontinue service without notice, if such action is necessary under the

circumstances. The telephone company may make changes in its communication facilities, equipment and operations

procedures, where such action is reasonably required in the operation of its business and is not inconsistent with the rules

and regulations of the Federal Communications Commission.

INDUSTRY CANADA REGULATIONS

NOTICE: The

Industry Canada

label identifies certified equipment. This certification means that the equipment meets

certain telecommunications network protective operational and safety requirements. The Department does not guarantee

the equipment will operate to the user's satisfaction.

- Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. In some

cases, the company's inside wiring associated with a single line individual service may be extended by means of a certified

connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions

may not prevent degradation of service in some situations.

- Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the

telecommunications company cause to request the user to disconnect the equipment.

- Make sure that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe

system, if present, are connected together.

CAUTION

: The installation of this equipment should only be undertaken by qualified personnel.

- The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a

telephone loop which is used by the device, to prevent overloading. The termination on a loop may consist of any

combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not

exceed 100.

Load Number for TPI-100 = 8

1 2 3 4 5 6 ... 16 17

Resumo do Conteúdo

Página 1

P82030 K Sheet 1 of 17 273 Branchport Avenue Long Branch, NJ 07740 Thank you for using our products. (800) 631-2148 www.wheelockinc.com

Página 2

P82030 K Sheet 10 of 17 WIRING INSTRUCTIONS (SEE FIGURE 9): CAUTION: Use class 2 power source only. 1. Make sure 24VDC power supply is disco

Página 3

P82030 K Sheet 11 of 17 Figure 9. Installation Programming, and Tone Volume Adjustment Diagram

Página 4

P82030 K Sheet 12 of 17 Figure 10. Connection to FZC-3 NOTES: 1. Set the FZC-3 “Talk Battery/TPI-100” selector switch to the “TPI-100” pos

Página 5

P82030 K Sheet 13 of 17 PROGRAMMING INSTRUCTIONS: There are five parameters in the TPI-100 which must be set to insure proper operation. These are

Página 6

P82030 K Sheet 14 of 17 Figure 13. Hang Up Tone Frequency Detector When shipped from the factory, the frequency is set to minimum (200Hz), and i

Página 7

P82030 K Sheet 15 of 17 "MAN." control, then the timer begins to time out when the page is initiated. Therefore "VOX" will prov

Página 8

P82030 K Sheet 16 of 17 TPI-100 TELEPHONE/PAGING RING START INTERFACE 1. Pick up the telephone handset and dial the line number assigned to the T

Página 9

P82030 K Sheet 17 of 17 county, province, district, federal and other applicable building and fire standards, guidelines, regulations, laws and code

Página 10

P82030 K Sheet 2 of 17 GENERAL APPLICATION INFORMATION: The Telephone Paging Interface (TPI-100) provides ring start (90V/20Hz) paging access from:

Página 11

P82030 K Sheet 3 of 17 Telephone "Hang Up" Tone One-Way Paging Talkback Paging One-Way Paging Using FZC-3 Zone Control Tone Detect Jumpe

Página 12

P82030 K Sheet 4 of 17 Zone 3 Chart 3. Paging Priorities for Multiple Line Applications Higher priority TPI-100's interrupt lower priority T

Página 13

P82030 K Sheet 5 of 17 Figure 3. Single Line One Zone, One-Way Paging With Central Amplifier and Transformer Equipped Speakers and Horns Figure 3

Página 14

P82030 K Sheet 6 of 17 Figure 5. Multiple Lines Zone and All Call Paging Figure 5 depicts a multi zone system with "All Call". The sy

Página 15 - OPERATING INSTRUCTIONS

P82030 K Sheet 7 of 17 Figure 6. Multiple Lines Zone, Group and All Call Paging Figure 6 depicts a multi zone system with group page and "A

Página 16 - Limited Warranty

P82030 K Sheet 8 of 17 There are three ways of accessing the zones with this configuration. First the zones may be accessed individually. Second,

Página 17 - Limitation of Liability

P82030 K Sheet 9 of 17 Supply Voltage (Nominal) -24VDC Supply Voltage Range -21.6VDC TO -26.4VDC Supply Current (Idle - BGM) 64mA (See Note 1)

Comentários a estes Manuais

Sem comentários

Wheelock TPI-100 Manual de Instruções

Consulte online ou descarregue Manual de Instruções para Máquina de Redução de Ruído Wheelock TPI-100. Wheelock TPI-100 Instruction manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais